鋼絲拉力試驗機

示值無規律的偏差

Eight, showing the value of deviation is irregular

齒桿、齒輪有油污、磨損或有毛刺：消除齒桿、齒輪的油污、毛刺，找出超差時的齒桿接觸點，然后修正齒桿、齒輪；如不能消除誤差．更換齒桿、齒輪。

 rack, gear oil, abrasion or burr: eliminate the rack, gear oil, burr, find out the pole difference when the contact points, and then modified tooth bar, gear; if not eliminate errors. Replace the tooth bar, gear.

拉力試驗機試驗機安裝不水平：調整水平。

tensile testing machine testing machine installation is not level: level adjustment.

齒桿彎曲：校直或更換齒桿，調整滾動槽輪的問隙。

toothed bar bending: alignment or replacement tooth bar, adjust the roll gap groove wheel.

鋼絲拉力試驗機計算機軟件聯機后出現提示框信息顯示超載。

Nine, computer software on-line prompt box display information overload.

解決方案是檢查計算機與試驗機的通訊線是否脫落;檢查聯機選擇傳感器是否選擇正確;檢查近的試驗或操作鍵

The solution is to check the computer and test machine communication line is off; check the online selection of sensor is correct; check the last test or operation keys

盤時傳感器是否被撞過;檢查出現問題之前是否使用了軟件的校準或標定功能;檢查是否手動更改過校準值、標定值或硬件參數中的其他信息。

When the sensor is knocked off; check whether the use of a software appears calibration or calibration before; check whether the manual modified calibration values, calibration information value or other hardware parameters in the.

試驗機主機電源不亮，不能上下移動。

Host ten, the power of the testing machine does not light, not to move up and down.

解決方案是檢查接入試驗機的電源線路是否連接正常;檢查急停開關是否處于擰起狀態;檢查接入試驗機的電源電壓是否正常;檢查機器插座上的保險是否燒斷，請取出備用保險絲安裝即可。

The solution is power line inspection access testing machine is connected properly; check the emergency stop switch is in screwed up state; power supply voltage check access testing machine is normal; check the socket on the insurance is burned off, remove the spare fuse can be installed.

試驗機主機電源有電但設備不可以上下移動。

Host eleven, testing machine power supply with power but the equipment can not move up and down.

解決方案是檢查是否是15S（時間）以后設備還無法移動，因為主機開機需要自檢，大概需要15S時間;檢查上下限位是否再恰當?shù)奈恢?，有一定的運行空間;檢查接入試驗機的電源電壓是否正常。

The solution is to check whether it is 15S （time） after the device is unable to move, because the host boot take self-inspection, probably need 15S time; check the upper and lower limit is again appropriate position, operating space; check supply voltage access testing machine is normal.

油源的保養：

Eight, oil source:

定期檢查主機和油源處是否有漏油的地方，如發現有漏油，應及時更換密封圈或組合墊;

regularly check the host and the supply of oil leaks place, if there is oil leakage, should be promptly replaced seal ring or a combined pad;

根據機器的使用情況及油的使用期限，定期更換吸油過濾器和濾芯，更換液壓油。

 according to the use condition and oil machine use period, replace the oil filter and filter periodically, replacing the hydraulic oil.

長時間不做試驗時，注意關斷主機電源。如果機器在待機狀態，轉換開關應打到“加載”檔，因為如果轉換開關打在“快退”檔，電磁換向閥一直在通電狀態，會影響 該器件的使用壽命。

Experiment 3, not long time, pay attention to shut off the main power. If the machine is in the standby state, the switch should call the "load" file, because if the switch on the "rewind" file, electromagnetic reversing valve has been in a power-on state, affect the service life of the device.

控制系統保養：

Nine, control system maintenance:

定期檢查控制器后面板的連接線是否接觸良好，如有松動，應及時緊固;

regularly check the controller panel connecting line is good contact, such as loose, should be timely fastening;

試驗后若有一段較長的時間不用機器時，關閉控制器和電腦;

after the test if there is a long time not machine closed, controller and computer;

控制器上的接口為一一對應，插錯接口可能對設備造成損壞;

the controller interface for the corresponding one one, inserted the wrong interface may cause damage to the equipment;

插拔控制器上的接口必須關閉控制器電源。

Swap Controller Interface must be shut down the power supply controller.